NOTE: The actual transmission fluid (HCF-2) capacity will vary from the specified capacity based on the length of time the transmission fluid pan is off the transmission. Avoid leaving the transmission fluid pan off for extend periods of time.
7.
Magnet - Remove
8.
Transmission Fluid Strainer - Remove
9.
Transmission Fluid Strainer - Check
1.
Clean the inlet opening (A) of the transmission fluid strainer (B) thoroughly with compressed air.
2.
Check that it is in good condition and that the inlet opening is not clogged.
3.
Test the strainer by pouring clean transmission fluid through the inlet opening, and replace it if it is clogged or damaged.
10.
Valve Body Assembly - Remove
1.
Remove the transmission fluid temperature sensor (A).
2.
Disconnect the connectors (B).
3.
Remove the guide plate (A).
4.
Remove the valve body assembly (B) straightly.
NOTE:
Do not remove the bolts with no ? marked on.
Check that the valve body assembly is free of solenoid wire harness A.
Be careful not to damage solenoid wire harness A.
11.
10.9 x 26 mm Pipe - Remove
12.
8 x 133.5 mm Pipe - Remove
13.
12 x 56.7 mm Pipe - Remove
14.
Joint Pipe - Remove
NOTE: Be careful not to drop the filter (A).
15.
10.9 x 18.5 mm Pipe - Remove
16.
14.3 x 36.2 mm Pipe - Remove
17.
18 x 18 mm Pipe - Remove
18.
Solenoid Wire Harness A - Remove
NOTE:
Where icon is shown, click for further information.
Keep all foreign particles out of the transmission.
Apply a light coat of clean transmission fluid on all O-rings before installation.
Be careful not to damage the O-rings.
Solenoid wire harness A and the transmission fluid temperature sensor are not available separately. Replace them as a set.
The valve body assembly and the following parts are not available separately. Replace them as a set.
?
CVT clutch pressure control solenoid valve
?
CVT drive pulley pressure control solenoid valve
?
CVT driven pulley pressure control solenoid valve
?
CVT lock-up clutch control solenoid valve
?
Shift solenoid valve B
?
Solenoid wire harness B
1
Detailed information, notes and precautions
Torque: N·m (kgf·m, lbf·ft)
Replace
1.
Solenoid Wire Harness A - Install
2.
18 x 18 mm Pipe - Install
3.
14.3 x 36.2 mm Pipe - Install
NOTE: You can install the pipe regardless of its direction.
4.
10.9 x 18.5 mm Pipe - Install
5.
Joint Pipe - Install
NOTE:
The joint pipe has the filter (A). The filter end should face the valve body assembly side.
Be careful not to drop the filter.
6.
12 x 56.7 mm Pipe - Install
NOTE: You can install the pipe regardless of its direction.
7.
8 x 133.5 mm Pipe - Install
8.
10.9 x 26 mm Pipe - Install
9.
Valve Body Assembly - Install
1.
Install the valve body assembly (A) straightly.
NOTE: Do not pinch solenoid wire harnesses A and B.
Bolt
Length
B
90 mm (3.54 in)
C
80 mm (3.15 in)
D
65 mm (2.56 in)
E
55 mm (2.17 in)
F
40 mm (1.57 in)
2.
Install the guide plate (G).
3.
Make sure each branch of solenoid wire harness A goes through the appropriate location, especially as shown, one (B) must be located to the inside from the other (C).
4.
Connect the connectors (D).
5.
Install the transmission fluid temperature sensor (E).
10.
Transmission Fluid Strainer - Install
NOTE: Do not pinch solenoid wire harnesses A and B.
11.
Magnet - Install
12.
Transmission Fluid Pan - Install
NOTE:
Tighten the transmission fluid pan mounting bolts in a crisscross pattern in at least two steps.
Do not pinch solenoid wire harnesses A and B.
13.
Connector (Solenoid Wire Harness A) - Connect
NOTE: Check the connector for corrosion, dirt, or oil, and clean or repair if necessary.
